Hello, welcome to Jinan Huawei CNC machinery CO., Ltd

National Advisory Service Hotline

Advanced Search:


Contact us


contact us

Contacts:JI Manager

Unified hotline:400-6587-688

Tel: (86)531-88276988

Fax:(86)531-88276988

Phone number:0086-15269186223

Address: No.18 Tonghua Road ,

Licheng district , Jinan city, 
shandong province, China



Company news

Carving knives identification and uses

Source: Time:2016-03-09 13:41:29 views:

Recognition carving knives, purpose
Engraving tool commonly divided into four categories: flat knife, straight knife (column knife), cutter, three-dimensional shaped knife.
Carving knives establishment Wentai carving software by clicking on the "2D" "3D" "cut" an entering any of the three options to complete the magazine; the tool library "central knife" tool is very idealistic, under normal circumstances it is not used to calculate the tool path.

1, flat knife W1: indicates the diameter of the tool shank, common shank diameter ∮3.175, ∮4, ∮6, root
It needs to set.
W2: represents tip width, it directly affects the carving effect, set to be as accurate as possible when you can take a ruler precision highs rough guides.
A: Half the angle between two sides of the nose portion of the tool if it is 30 °, then A is set to 15, and so on.
Be carving materials: color board, PVC board, plexiglass, ABS panels.
You can cut material: color plate, ABS plate.
Knife principle: The small print carved with W2 or knife A small point, as far as possible with a machete when the characters in order to improve the processing speed; Tool selection to the narrowest strokes prevail; if necessary, under the premise does not affect the font effects, available node editing strokes in order to facilitate the path through the sword; engraving badges commonly used tool 30 °; if the word is too small can be replaced after a single line with the "cut" count path.

2, straight knife (blade column) W1: width of the front end portion of the tool blade, a common width 2MM, 1.5MM, generally set a little smaller, because the front end is easy chip removal, repair grind the side edge, so The actual width a little smaller.
H1: Length of the tool edge, the cutting edge of the material should be less than the height of the Minister, the general H1 is about 5MM can.
Be carving materials: color board, PVC board, plexiglass, ABS panels.
You can cut material: color plate, ABS plate.
As the result of the tool used for engraving characters on the licensing department, licensing department so called knife, carving effect but slightly lower than the same width flat knife. It cut the edges of the material for the straight edge, while the flat side of a knife cut out more material there is a bias, depending on the inclination of the tool angle, depending on angle, on the edge of the slope bigger.
3, the cutter W1: width of the front end of the tool, common shank diameter ∮3.175, ∮4, ∮6; if the material thickness is less than 10MM cutting the small print when using ∮3.175 knife cutting word to be deformed, sometimes with the shank diameter of the tip is changed from ∮3.175 ∮2 or ∮1.5 becomes the tool handle to cut.
H1: Minister of blade, cut the material should be less than the thickness of the blade of his minister, according to the general H1 thickness of the material is divided into the following categories (more than cutting material 2mm, easy chip removal).
12mm: The following materials and cut 10MM
17mm: cut 15MM material
22mm: cut 20MM material (PVC multi ∮3.175; acrylic with ∮4)
Laser marking material: PVC board, plexiglass, wood and the like.
Can cut material: PVC board, plexiglass, wood and the like.
Knife principles: not recommended to use the tool cutting 10MM 22mm and below the material may result in cutting knife; 22mm when no tool, but also cut 20MM material, temporary use 17mm cutter, cutting through layering to achieve.
4, three-dimensional shaped knife because this tool is different from our common alloy handle material with a direct repair work required to grind a variety of carving knives, but under ∮6 hilt through a special welding process of welding was heads of various shapes, for a variety of direct engraving special shape, so called bulk knife.
W1: The following handle the bulk of the knife diameter, the random distribution of 32mm; also have a smaller one, for cutting
Cut a small three-dimensional characters.
A: The two sides of the half angle of the tip portion, because the random distribution of the tool is 90 °, then A is set to 45 (similar to the flat knife)
W2: tip width because the specific calculation of three-dimensional path, the path is requested through the knife, no longer much meaning, usually set to 0.1 or 0.2.
Tool Usage: three-dimensional clearance angle word (calculated using the "3D" function path) and back down the hypotenuse of carved crystal card use.
5, the other dedicated to the milling cutter mesa end milling cutter; relief tool used when making relief; wooden pallet made with various types of lace lace knives.

keys: 

Previous:Already the first article

next:Purchase engraving machine must consider the full

Return